Subscribe to the EPMA Mailing List

Euro PM2009 Proceedings: Powder Injection Moulding

  • : EPMA
  • : EPMA
  • : PDF Download
  • : 2009

Euro PM2009 Congress Technical Presentations on Metal Injection Moulding.

This download contains the following papers:

Metal Injection Moulding of Fe8Ni Micronic Pre-Alloyed Powders

Powder Injection Moulding of Titanium from TiH2 Powders
E. Carreño-Morelli, W. Krstev, B. Romeira, M. Rodriguez-Arbaizar, J.-E. Bidaux, S. Zachmann

Influence of Particle Size Distribution and Chemical Composition of the Powder on Final Properties of Inconel 718 Fabricated by Metal Injection Moulding (MIM)
J.M. Contreras, Jiménez-Morales and J.M. Torralba

Influence of Sintering Conditions and Furnace Technology on Chemical and Mechanical Properties of Injection Moulded 316L
Steffen Krug

Recycling of Ferrous Powders by Powder Injection Moulding Process

Effects of Boron Addition on Microstructure and Mechanical Properties of Ti-6Al-4V Metal Injection Moulding Components Using a Water Soluble Binder
A. T. Sidambe, I .A. Figueroa, M. H. Ismail, H. Hamilton, I. Todd

Spray Drying Technique as a Method for Improving Rheology of Alumina Feedstocks for Powder Injection Moulding
B. Arias-Serrano, P. Thomas-Vielma, A. Várez, B. Levenfeld, S. Martinerie, and E.Carreño-Morelli

Metal Injection Moulding (MIM) of Titanium-Aluminides
W. Limberg, T. Ebel, F. P. Schimansky, R. Hoppe, M. Oehring, F. Pyczak

Effect of Solid Loading on Final Properties of Alumina Parts obtained by Powder Injection Moulding
P. Thomas-Vielma, B. Arias-Serrano, J. Y. Pastor, B. Levenfeld and A. Várez

Densification Behaviour of MIM 316L Parts during Vacuum Sintering
Borivoj Šuštaršič, B. Boštjan Berginc, Zlatko Kampuš

Sintering Study of CP-Ti and Ti6V4Al Metal Injection Moulding Parts Using Taguchi Method
A.T.Sidambe, I. A. Figueroa, H. Hamilton, I. Todd

Review of Developments in Gas Atomised Alloy Metal Powders for MIM Applications
Keith Murray and Martin Kearns

Microstructural Analysis of Duplex Stainless Steels Produced by Powder Injection Moulding
M. E. Sotomayor, J. L. Baldonedo, B. Levenfeld, A. Várez

Multi Component Powder Injection Moulding of Metal-Ceramic-Composites
Baumann A., Moritz T., Lenk R.

Thermodynamic Simulation of 316L and 17-4PH Stainless Steels Using Different Process Conditions
for Two Components Metal Injection Moulding (2C-MIM)
Benedet Dutra, G., Mulser, M., Petzoldt F.

Metal Injection Moulding of Carbides Reinforced M2 HSS
G. Herranz, G. Matula, R. Alonso, I. Sánchez, G. Rodríguez

Powder Injection Moulding of Stainless Steels Reinforced with Nano Size Alumina Particles
H. Özkan GÜLSOY,Tarık BAYKARA and Sunullah ÖZBEK

Extrusion and In-Line Calibration of Hollow Profiles based on MIM-Feedstocks
C. Aumund-Kopp, F. Petzoldt, T. Schäfter

Evaluation of the Supercritical CO2 as Method of Debinding for PIM Parts
L. Federzoni, P.Revirand, G. Lumia, D. Rossignol

Ceramic Components for Automotive and Railway Applications Made by Two-Component Ceramic Injection Moulding
Tassilo Moritz, Anne Mannschatz

Process Stability and Quality Surveillance in the Metal Injection Moulding Process - Towards Zero Rejection Based on an Artificial Neuronal Network
Julian Schwenzel, Frank Petzoldt

MIM-Simulation: A Virtual Study on Phase Separation
Dr. Marco Thornagel

Measurement Methods for Powder Binder Separation in PIM Components
Martin Jenni, Rudolf Zauner and Jürgen Stampfl

Modelling of the Thermal Debinding Behavior of Copper MIM Parts Using Thermo-kinetic Analysis
Ijaz Ul Mohsin,Daniel Lager, Herbert Danninger, Wolfgang Hohenauer, Christian Gierl

Using a Helium Pycnometer as a Quality Tool in Powder Metal Injection Moulding
Robert Sanford

Go To Top